Contact us

What we measure

The instruments behind every reading.

Each reading on IoTyX starts with an instrument in the field, read by an Ilonnati controller. These are the typical instruments for each reading, with their ranges; the model is chosen for each site.

Instruments
11 types
Connections
RS-485 Modbus, 4–20 mA, pulse, wireless
Read by
An Ilonnati controller on site
Illustration of a town water system: treatment works, an elevated reservoir, a pump house, the main with motorised valves, homes with meters, and an Ilonnati controller beside each valve and pump.

Where they are fitted

  1. Elevated reservoir
  2. Pump set
  3. Motorised valve
  4. Meter at each connection
  5. Ilonnati controller

Water quantity

How much water moves, from the source to the connection: the figure every loss calculation starts from.

2 instruments

  • Electromagnetic flow meter

    Measures flow in a full pipe with no moving parts, for bulk metering at a source, a zone inlet or a plant.

    Pipe sizes
    3 to 3,000 mm
    Velocity
    0.1 to 15 m/s, 1 mm/s resolution
    Accuracy
    ±0.3% of reading above 1 m/s (25–600 mm pipes)
    Outputs
    4–20 mA, pulse, frequency, RS-485 Modbus
    Power
    220 V AC or 24 V DC
    • Forward, reverse and net totals
    • Alarms for an empty pipe, and for high and low flow
    • Outputs isolated from the line

    Fitted at Source and zone inlets, treatment works, plant process lines

  • Mechanical water meter with a pulse sensor

    A Class B bulk meter whose dial is read by a clip-on pulse sensor, so an existing meter can report without being replaced.

    Sizes
    40 to 500 mm
    Permanent flow
    15 m³/h at 40 mm to 1,500 m³/h at 500 mm
    Accuracy
    ±3% low-flow zone, ±1.5% upper zone
    Pulse
    One per 10, 100 or 1,000 litres, by size
    Pressure
    Up to 10 bar
    • Mechanism lifts out for service; the meter stays in the pipe
    • Dry, sealed dial, not affected by external magnets
    • Needs 10 pipe diameters of straight pipe before it and 5 after

    Fitted at Connections, bulk supply points, campuses and housing

Level and pressure

How full each tank is, and whether each zone of a network is being supplied.

2 instruments

  • Pressure transmitter

    Reports the pressure in a main, so low pressure, a burst or an unserved zone shows at once.

    Range
    0–6 or 0–10 bar
    Accuracy
    0.5%
    Output
    4–20 mA
    Build
    IP65, 316L stainless steel
    Supply
    12 or 24 V DC
    • Read by the controller through an analog input
    • Works from −20 to 80 °C

    Fitted at Mains, zone boundaries, pump delivery lines

  • Radar level sensor

    Measures the level of a tank, sump, reservoir or river from above, without touching the water.

    Range
    0.3 to 12 m
    Accuracy
    ±2 mm, 1 mm resolution
    Beam
    60 GHz, 8°
    Build
    IP68
    Power
    Own battery, around seven years at one report a day
    • Not affected by dust, condensation or temperature
    • Alarms on a threshold, a sudden change and its own tilt
    • Keeps 2,000 readings and resends them after an outage

    Fitted at Overhead tanks, sumps, reservoirs, rivers and sewers

Water quality

Whether water is fit to drink or to discharge, measured continuously or sampled at set intervals.

3 instruments

  • Water-quality probes

    Digital probes for pH, conductivity and TDS, nitrate and residual chlorine, each read over RS-485 Modbus.

    pH
    0–14, ±0.05
    Conductivity
    Up to 30,000 or 500,000 µS/cm, ±1% of full scale
    Nitrate
    0.1 to 1,000 mg/L
    Residual chlorine
    0–5, 10 or 20 mg/L, ±1% of full scale
    Build
    IP68, 10 m cable (to 100 m)
    • Calibration is stored in the probe, so a probe calibrated in the lab is swapped on site
    • Temperature measured for compensation
    • The chlorine probe sits in a flow cell, with water flowing past it

    Fitted at Treatment works, reservoirs, distribution points, plant water

  • Chlorine analyser

    A sampling analyser for residual chlorine, where a reading is taken at a set interval rather than continuously.

    Alarms
    Low and high set points, 0–10 mg/L
    Link
    RS-485, up to 255 on one line
    • Warns when reagent is low or old, or there is no sample
    • Reports calibration errors and readings out of range

    Fitted at Treatment works and service reservoirs

  • pH and redox converter

    Turns a pH or redox (ORP) electrode into a reading the controller can take, with its calibration history.

    Range
    pH 0–14, or ORP ±1,500 mV
    Accuracy
    ±0.5% of range
    Build
    IP67, RS-485 Modbus
    • Keeps its last five calibrations, with dates
    • A calibration-due reminder, set from 0 to 365 days

    Fitted at Treatment, effluent and process water

Air

The air at a city junction, a plant boundary or a mine, averaged for comparison with the standards.

1 instrument

  • Outdoor air-quality station

    A station for up to eight air readings, for a city, a plant boundary, a mine or a tunnel.

    Particulates
    PM2.5 and PM10, 0–1,000 µg/m³
    Gases
    CO, O₃, NO₂, SO₂, CO₂ and total VOCs
    Weather
    Temperature, humidity, air pressure
    Reporting
    Every minute to every 24 hours
    Power
    Mains, or solar for at least 96 hours without sun
    • Averages over 1 minute, 1 hour and 24 hours, to compare with the standards
    • Mounts on a wall, roof, pole or the ground
    • Links over RS-485, Wi-Fi, Ethernet or 4G

    Fitted at City junctions, plant and mine boundaries, campuses

People

How many people use a space, counted from the ceiling without recording images.

1 instrument

  • Ceiling people counter

    Counts people in and out of a doorway or a hall from the ceiling, without recording images.

    Accuracy
    Up to 99.8%
    Mounting
    Up to 3.5 m, or 6.5 m for high ceilings
    Lines
    Up to four counting lines, both directions
    • Captures no images and works in the dark
    • Leaves out staff wearing a tag, and people who turn back
    • Queue regions with dwell time

    Fitted at Cafeterias, entrances, halls and waiting areas

Networks

How the readings reach IoTyX: a gateway for battery-powered wireless sensors, and the controller itself.

2 instruments

  • Wireless sensor gateway

    Gathers readings from battery-powered wireless sensors across a site and passes them to IoTyX.

    Sensors
    More than 2,000
    Reach
    About 2 km in a built-up area, up to 15 km in open line of sight
    Back link
    Ethernet, Wi-Fi or 4G, switching between them by itself
    Build
    IP65, −40 to 70 °C
    • Desk, wall or pole mounting
    • Speaks to building management systems over BACnet/IP

    Fitted at Campuses, housing, plants and large sites

  • Ilonnati controller

    The controller beside each machine, built on Ilonnati’s 4G/LTE board: it reads the instruments, drives the valve or pump, and reports to IoTyX.

    Link
    LTE Cat 1, two SIM slots
    Inputs
    RS-485 Modbus, CAN, analog inputs, encoder
    Drives
    A valve actuator or a pump
    Supply
    5 to 60 V DC, 2 A
    Enclosure
    IP65/68, −40 to 85 °C
    • A backup battery that reports a power failure
    • Firmware updates over the air
    • Designed by Ilonnati in Hyderabad

    Fitted at Beside every valve, pump, tank and machine it runs

IS 10500:2012

Drinking-water limits

The limits in the Bureau of Indian Standards’ drinking water specification for the readings the probes take. IoTyX raises an alert when a reading crosses the limit set for it.

IS 10500:2012, the standard
ParameterAcceptable limit
pH6.5 to 8.5 (no relaxation)
Total dissolved solids500 mg/L (2,000 mg/L permissible)
Residual free chlorineAt least 0.2 mg/L (1.0 mg/L permissible)
Nitrate45 mg/L (no relaxation)
Fluoride1.0 mg/L (1.5 mg/L permissible)
Arsenic0.01 mg/L (no relaxation)

Tell us what you need to connect, monitor or control

An engineer will reply.