Contact us

Environment and agriculture

What the land holds, measured field by field.

Smart soil sensors for moisture, salinity, NPK, contamination and compaction, mapped field by field and surveyed by drone, so land is managed on its measured condition.

In the field
Ilonnati controllers and sensors
On the screen
IoTyX: web, phone, control room
Illustration of environmental monitoring and farming: an air-quality station, a buoy and a level gauge on a river, fields with soil sensors and a drip main, a polyhouse, and a drone over the forest, with Ilonnati controllers.

On a typical site

  1. Air-quality station
  2. River buoy
  3. Soil sensors
  4. Flood level gauge
  5. Ilonnati controller

In short

Soil changes slowly and out of sight. Salt builds up, nutrients run down, ground compacts under machinery, and a field can carry contamination no one has measured. Smart soil sensors read moisture, salinity, nitrogen, phosphorus and potassium (NPK), contamination and compaction where they are placed, and report through an Ilonnati controller to IoTyX. Each field is set on a GIS map with its readings, so differences across a farm or a district show at a glance, and drone surveys cover land too large to probe point by point. AI predicts crop yield from the record, and a digital twin of the farm models it.

Who it is for

  • Agriculture and horticulture departments
  • Large farms and plantations
  • Agricultural universities and research stations
  • Farmer producer organisations
  • Bodies restoring degraded land

Before and after

What changes

The same job, today and with Ilonnati.

  1. Today: Soil is sampled once a season and sent to a laboratory. With Ilonnati: Sensors in the field report moisture, salinity and nutrients as they change.
  2. Today: One sample stands for a whole field. With Ilonnati: Readings from several points are mapped, so differences across the field show.
  3. Today: Fertiliser is applied by habit. With Ilonnati: NPK readings show what each field holds, so fertiliser is matched to it.
  4. Today: Salt and contamination are found when a crop fails. With Ilonnati: Rising salinity and contamination are flagged while there is time to deal with them.
  5. Today: Large holdings are walked, or not checked at all. With Ilonnati: Drone surveys cover land too large to walk, and sit on the same map as the sensors.

How it works

From the reading in the field to the action on the screen, and back.

  1. 01

    Sensors in the soil

    Smart soil sensors are placed across each field at points chosen for the soil and the crop, and wired to an Ilonnati controller.

  2. 02

    Readings reach IoTyX

    Moisture, salinity, NPK, contamination and compaction readings arrive with their place and time.

  3. 03

    Mapped field by field

    A GIS map shows each field with its latest readings, so a salty corner or a strip low in nutrients stands out.

  4. 04

    A reading crosses its mark

    Salinity rising past its threshold, or moisture falling below it, alerts the person responsible for that land.

  5. 05

    A survey from above

    A drone survey covers land too large to probe point by point, and its results are placed on the same map.

  6. 06

    Yield and planning

    AI predicts crop yield from the record, and a digital twin of the farm is used to try changes before they are made in the field.

What is measured

Each reading reaches IoTyX through the Ilonnati controller beside the equipment.

ReadingWhat it tells you
Soil moistureWater held in the root zone, for irrigation and for signs of crop stress
SalinitySalt building up in the soil, often from irrigation water or poor drainage
Nitrogen, phosphorus, potassiumThe main nutrients available to the crop, so fertiliser matches the need
ContaminationPollutants in the land that make it unfit or unsafe for a crop
CompactionGround packed hard by machinery, which roots and water cannot get through
Predicted crop yieldExpected yield by field, predicted from the readings

The rules and programmes behind it

Public programmes and rules that ask for this kind of measurement. Each links to the body that publishes it.

Industries where it applies

Each industry page sets out its equipment, its rules and the other use cases that run there.

Questions buyers ask

Not answered here?

Ask about your own network, plant or campus. An engineer will reply.

Contact us
01What do the soil sensors measure?

Moisture, salinity, nitrogen, phosphorus and potassium (NPK), contamination and compaction. Which of them a site needs is agreed before installation.

02Can the same readings run the irrigation?

Yes. The moisture readings can open a field’s irrigation valve when its soil dries to the set level, and close it when the soil is wet enough.

03What are the drones used for?

Precision surveys over land too large to cover with sensors point by point. Their results are placed on the same map as the sensor readings.

04What does the digital twin of the farm do?

It models the farm from its readings, so changes can be tried on the model before they are made in the field.

Tell us what you need to connect, monitor or control

An engineer will reply.