Contact us

Environment and agriculture

A mine’s dust, erosion and boundary, on one map.

Drone surveys of erosion and dust plumes, a GIS map of the mine’s boundary, and stations that can measure air and water where the site meets its neighbours.

In the field
Ilonnati controllers and sensors
On the screen
IoTyX: web, phone, control room
Illustration of a mine site: a terraced open pit with a haul truck, the crusher and conveyor, stockpiles, a dust monitor, a borewell with a flow meter, and a survey drone, with Ilonnati controllers.

On a typical site

  1. Dust and air monitor
  2. Borewell flow meter
  3. Survey drone
  4. Crusher and conveyor
  5. Ilonnati controller

In short

A working mine moves ground every day, and its dust and run-off do not stop at the fence. Drones survey erosion and dust plumes over areas too large to walk, and a GIS map holds the mine’s boundary, with every survey and station placed on it. At the boundary an outdoor station can measure PM10, PM2.5 and gases; at ponds and outfalls, probes can measure pH, conductivity, nitrate and turbidity, and a radar sensor can read the level. AI analyses risk from the record, and a digital twin of the mine’s operations shows the site as it runs, for safety and compliance.

Who it is for

  • Opencast and underground mine operators
  • Mining contractors
  • Public sector mineral corporations
  • State mining and geology departments
  • Pollution control boards

Before and after

What changes

The same job, today and with Ilonnati.

  1. Today: Dust is judged by eye from the haul road. With Ilonnati: A station at the boundary can report PM10 and PM2.5 every minute, with an alert at its limit.
  2. Today: Erosion on dumps and slopes is noticed after a slip. With Ilonnati: Drone surveys record erosion across the site on a schedule, each compared with the last.
  3. Today: Dust plumes are seen, but not where they go. With Ilonnati: Drone surveys record the plumes, and the map shows where they cross the boundary.
  4. Today: Mine water is sampled by hand, now and then. With Ilonnati: Probes at ponds and the outfall can report pH, conductivity and turbidity continuously.
  5. Today: The boundary lives on a lease plan in an office. With Ilonnati: The boundary is on a GIS map, with every station and survey placed against it.

How it works

From the reading in the field to the action on the screen, and back.

  1. 01

    The boundary mapped

    The mine’s boundary, pits, dumps, ponds and haul roads are placed on a GIS map of the site.

  2. 02

    Stations at the edge

    Air stations can stand along the boundary, on mains or solar power, with water probes and level sensors at ponds and outfalls.

  3. 03

    Surveys from above

    Drone surveys record erosion and dust plumes across the whole site, and each is compared with the one before.

  4. 04

    A reading crosses its limit

    PM10 at the boundary rises above its threshold during haulage, and the site’s environment officer is alerted.

  5. 05

    Risk and operations

    AI analyses risk from the readings and surveys, and a digital twin of the mine’s operations shows the site as it runs.

  6. 06

    Records for compliance

    Every reading and survey is kept with its place and time, for the mine’s compliance reports.

What is measured

Each reading reaches IoTyX through the Ilonnati controller beside the equipment.

ReadingWhat it tells you
ErosionWhere dumps, slopes and banks are wearing away, from drone survey
Dust plumesHow far dust travels from blasting and haulage, from drone survey
BoundaryEvery station and survey placed against the mine’s mapped boundary
PM10 and PM2.5Dust at the boundary, which an outdoor air station can measure every minute
GasesCO, NO₂ and SO₂, which the same station can measure, underground too
Mine water qualitypH, conductivity, nitrate and turbidity, which probes can measure
Pond and sump levelHow full a settling pond or sump is, which a radar sensor can read

The rules and programmes behind it

Public programmes and rules that ask for this kind of measurement. Each links to the body that publishes it.

Industries where it applies

Each industry page sets out its equipment, its rules and the other use cases that run there.

Questions buyers ask

Not answered here?

Ask about your own network, plant or campus. An engineer will reply.

Contact us
01What does the drone survey record?

Erosion across the site, and dust plumes, over areas too large to cover on foot. Each survey is placed on the same map as the station readings.

02Which readings can the stations take?

An outdoor air station can measure PM2.5, PM10 and gases such as CO, NO₂ and SO₂ at the boundary. Water probes can measure pH, conductivity, nitrate and turbidity at ponds and outfalls. Which are fitted is agreed for each mine.

03Can stations run without mains power?

The air station can run on solar power, for at least 96 hours without sun, and the radar level sensor on its own battery. Power and the mobile link are planned for each station.

04Does it work underground?

The air station is built for open air, tunnels and underground spaces. How its readings leave an underground working is planned for each mine.

Tell us what you need to connect, monitor or control

An engineer will reply.