Industries: Mining
Mine sites, watched for dust, erosion and water.
For mine operators and the bodies that oversee them: drone surveys of erosion and dust plumes, a mapped boundary, and stations that can measure air and water where the site meets its neighbours.
- Use cases
- 6 described below
- To start
- A pilot at one site
On a typical site
- Dust and air monitor
- Borewell flow meter
- Survey drone
- Crusher and conveyor
- Ilonnati controller
In short
A mine changes its ground every day, and what it releases is judged at the boundary. Ilonnati maps the mine’s boundary on GIS, surveys erosion and dust plumes by drone, and places stations where they tell the most: an air station can measure particulates and gases at the edge of the site, and probes can measure the water in ponds and at the outfall. AI analyses risk from the record, and a digital twin of the mine’s operations shows the site as it runs. Machines and vehicles on the site can join the same platform, so safety and compliance are seen in one place.
Why it is hard
The challenges
What makes mining hard to run without live measurement.
What Ilonnati runs hereDust that leaves the site
Blasting, haulage and crushing raise dust that does not stop at the fence, and neighbours notice it before a report does.
Erosion on slopes and dumps
Benches, dumps and banks wear away with every monsoon, and a large site is surveyed too rarely to see it early.
Water on and off the site
Pit water, settling ponds and run-off all need watching, and are usually sampled by hand.
Safety and compliance
A mine has to show that it meets the conditions it works under, between one inspection and the next.
What Ilonnati measures and runs
Ilonnati controllers and sensors on the equipment, IoTyX on the screen.
Erosion and dust plumes
Surveyed by drone across the whole site, and compared with the survey before.
Air at the boundary
An outdoor station can measure PM10, PM2.5 and gases every minute, on mains or solar.
Mine water
Probes can measure pH, conductivity, nitrate and turbidity at ponds and outfalls.
Pond and sump levels
A radar sensor can read the level of a settling pond or sump without touching the water.
The boundary
The mine’s boundary on a GIS map, with every station and survey placed against it.
Machines and vehicles
Machine condition, and each vehicle’s location from the vehicle module, on the same platform.
Use cases
Each has a page of its own: the situation, how it works and what is measured.
Mine site monitoringErosion, dust plumes and the boundary of a mine, watched by drone survey and station, for safety and compliance.MeasuresErosion, Dust plumes, Boundary
Air quality monitoringOutdoor stations for particulates, gases and noise, reporting as often as every minute to a map.MeasuresPM2.5, PM10, Nitrogen dioxide (NO₂)
Environmental complianceAir, water and noise measured around the clock at a site, each reading checked against its limit as it arrives.MeasuresPM2.5 and PM10, NO₂, SO₂ and CO, Noise
Water quality monitoringpH, turbidity, residual chlorine, TDS and nitrate measured continuously, from the treatment works to the far end.MeasurespH, Turbidity, Residual chlorine
Predictive maintenanceVibration, temperature, voltage and current on pumps, motors and HVAC, so a fault is found before the machine stops.MeasuresVibration, Temperature, Voltage
Fleet monitoringWhere each vehicle is, the fuel it burns and how it performs, with routes and driving analysed for cost.MeasuresLocation, Fuel consumption, Performance metrics
The rules and programmes behind it
Public programmes and rules that ask for this kind of measurement. Each links to the body that publishes it.
Any project that needs a CGWA groundwater permit must fit a digital flow meter with telemetry on every borewell.
CGWA guidelines, 2020, Ministry of Jal Shakti500 m³
A project drawing more than 500 m³ of groundwater a day needs two piezometers, one of them with a telemetered water level recorder.
CGWA guidelines, 2020, Ministry of Jal Shakti40 µg/m³
India’s National Ambient Air Quality Standards cover 12 pollutants; the annual limit for PM2.5 is 40 µg/m³.
National Ambient Air Quality Standards, CPCB, 2009
Questions buyers ask
Ask about your own network, plant or campus. An engineer will reply.
Contact us01What is monitored at a mine?
Erosion and dust plumes by drone survey, and the mine’s boundary on a GIS map. Stations can add air readings at the boundary and water readings at ponds and outfalls; which ones is agreed for each mine.
02What are the drones used for?
Surveys of erosion and dust plumes over areas too large to cover on foot, placed on the same map as the station readings.
03Can stations run where there is no mains supply?
The air station can run on solar power for at least 96 hours without sun, and the radar level sensor on its own battery. Power and the mobile link are planned for each station.
Related industries
The same hardware and the same platform, set up for other sites in environment and agriculture and beyond.
Environment and agricultureAgriculture and foodIrrigation that runs on the soil’s readings, and land health measured field by field.
Environment and agricultureSmart citiesWaste, traffic, noise, air and water across a city, on one map divided by service zone.
Environment and agricultureDisaster managementFlood levels, ground movement, slope stability and snow cover, measured for early warning and response planning.
Environment and agricultureForestryGreen cover, canopy and forest health measured by drone survey and ground sensors, for forests and afforestation.
