Contact us

Industry and energy

Every cubic metre of gas, accounted for.

Gas flow measured where it enters the site and where it is used, so consumption is known per department and per piece of equipment, and unusual flow is caught early.

In the field
Ilonnati controllers and sensors
On the screen
IoTyX: web, phone, control room
Illustration of an industrial site: a plant hall, a rotary kiln on its piers, cement silos and a conveyor, a substation with two transformers, a solar array and a wind turbine, with an Ilonnati controller beside each.

On a typical site

  1. Rotary kiln
  2. Drive motor
  3. Substation
  4. Solar and wind
  5. Ilonnati controller

In short

Gas is often bought through one meter and shared across boilers, furnaces, ovens and kitchens, so nobody knows which of them used what. Ilonnati measures gas flow in real time at the supply point and at the departments and equipment that draw it. IoTyX turns the readings into consumption reports by department and by equipment, for cost control and for comparing one user with another. Flow where there should be none, or more than a user should draw, raises an alert, so a leak or theft is looked for at once rather than at the end of the billing period.

Who it is for

  • Plants with gas-fired boilers and furnaces
  • Industrial parks with a shared gas supply
  • Commercial kitchens and campuses
  • Energy and utilities managers

Before and after

What changes

The same job, today and with Ilonnati.

  1. Today: Gas is read from one meter at the gate, once a month. With Ilonnati: Gas flow is measured in real time at the supply point and at each user.
  2. Today: The bill is split between departments by estimate. With Ilonnati: Consumption is reported per department and per piece of equipment, as measured.
  3. Today: A leak or theft shows up only as a larger bill. With Ilonnati: Flow when nothing on the line should be drawing raises an alert at once.
  4. Today: A furnace that burns more than last month goes unnoticed. With Ilonnati: Each furnace’s use is trended, so one that starts to draw more stands out.

How it works

From the reading in the field to the action on the screen, and back.

  1. 01

    Meters where gas flows

    Flow meters at the supply point and on the lines to each department or major user report to IoTyX through a controller.

  2. 02

    Consumption adds up

    Flow is totalled into consumption by hour, day and month, for each department and each piece of equipment.

  3. 03

    Unusual flow

    Gas flows to a line at night while its equipment is off, and the person responsible for the line is alerted.

  4. 04

    Checked on the ground

    The line is checked, and the cause, a leak or a valve left open, is found before more gas is lost.

  5. 05

    Reports for costing

    Monthly reports per department and per piece of equipment put a measured gas cost against each, for budgets and comparison.

What is measured

Each reading reaches IoTyX through the Ilonnati controller beside the equipment.

ReadingWhat it tells you
Gas flowWhat is flowing to each line now, and flow where there should be none
Consumption by departmentWhat each department used, for costing and budgets
Consumption by equipmentWhich boilers, furnaces or ovens use the most gas, and how that changes
Supply against usersGas lost between the supply point and the equipment, through leaks or theft
Line pressureWhether each user receives gas within its working band

Industries where it applies

Each industry page sets out its equipment, its rules and the other use cases that run there.

Questions buyers ask

Not answered here?

Ask about your own network, plant or campus. An engineer will reply.

Contact us
01What does it measure?

Gas flow and consumption in real time, at the supply point and at the departments and equipment that use it.

02Can costs be split by department?

Yes. Reports show the gas used per department and per piece of equipment, so each carries its measured share of the cost.

03Can it find a gas leak?

It flags the signs of one in the flow: gas moving while the equipment on a line is off, or more gas entering the site than its users account for. Leaks into the air around equipment are picked up by the gas detectors of industrial safety monitoring.

04What about gas cylinders in a kitchen?

On campuses, cylinder banks are monitored for which cylinders are in use and how full they are, so a replacement is ordered before service.

Tell us what you need to connect, monitor or control

An engineer will reply.