Water and utilities
A village water scheme, run from a phone.
A controller at the pump house, level sensors in the tanks, meters at the source and the households, and IoTyX to show whether every home, out to the tail end, is getting water.
- In the field
- Ilonnati controllers and sensors
- On the screen
- IoTyX: web, phone, control room
On a typical site
- Elevated reservoir
- Pump set
- Motorised valve
- Meter at each connection
- Ilonnati controller
In short
A rural scheme draws from a borewell, spring or intake, stores water in a service reservoir or overhead tank, and supplies households along branch and distribution lines out to the tail end. Ilonnati places a controller at the pump house and level sensors in the tanks, so the pump starts when the tank falls to its low mark and stops at the high one, without an operator walking to the switch. A bulk meter at the source records what is drawn each day. Pressure sensors and household meters show whether the tail end is served. Quantity, pressure, quality and system status for every village sit on one screen.
Who it is for
- Rural water supply and public health engineering departments
- District and block engineering offices
- Gram panchayats and village water committees
- Multi-village schemes fed from one source
- Contractors who build and run village schemes
Before and after
What changes
The same job, today and with Ilonnati.
- Today: An operator walks to the pump house to switch the pump on and off. With Ilonnati: The pump starts at the tank’s low mark and stops at its high mark, and can be run from a phone.
- Today: The overhead tank overflows unnoticed, or runs dry before supply time. With Ilonnati: The tank reports its level as it changes, with alerts for overflow and for a tank running low.
- Today: What the village received is guessed from the pump’s hours. With Ilonnati: A bulk meter at the source records what is drawn each day, and household meters what is delivered.
- Today: Tail-end households report a shortfall days after it starts. With Ilonnati: Pressure at the tail end shows at once whether the last connections are getting water.
- Today: An engineer covering many villages learns of a fault on the next visit. With Ilonnati: Every village shows on one map, and a device that stops reporting raises an alert.
How it works
From the reading in the field to the action on the screen, and back.
- 01
The pump starts
At the set time, or when the overhead tank falls to its low mark, the controller at the pump house starts the pump.
- 02
The tank fills
The level sensor reports as the tank fills. At the high mark the pump stops, so the tank does not overflow.
- 03
Supply goes out
The outlet valve opens for the village’s supply slot, and the bulk meter counts what goes out to the lines.
- 04
The tail end is checked
Pressure at the last connections shows whether they are served, and household meters show what each home received.
- 05
Quality is watched
pH and turbidity are measured at the intake and in the tank, and a reading outside its limit raises an alert.
- 06
Every village, one screen
Quantity, pressure, quality and the status of each device, for every village in the scheme, on a phone or in the office.
What is measured
Each reading reaches IoTyX through the Ilonnati controller beside the equipment.
| Reading | What it tells you |
|---|---|
| Overhead tank level | When to pump, before the tank overflows or runs dry |
| Water drawn at the source | How much the borewell or intake gives each day |
| Daily supply | What the village received each day, to set against the population it serves |
| Tail-end pressure | Whether the last households on the line are getting water |
| Household consumption | What each connection receives, and where water is lost on the way |
| pH and turbidity | Whether the water supplied is within its drinking-water limits |
| Pump state and hours | Whether the pump runs when it should, and for how long |
The rules and programmes behind it
Public programmes and rules that ask for this kind of measurement. Each links to the body that publishes it.
55 L
Jal Jeevan Mission counts a rural tap as functional only if it gives at least 55 litres per person per day, of BIS 10500 quality, on a regular schedule.
Jal Jeevan Mission, Functionality Assessment 202476%
In the 2024 national assessment, 76% of rural household taps met all three tests. Damaged pipelines (31.9%) and pump failures (29.6%) were the most common reasons a tap stopped working.
Jal Jeevan Mission, Functionality Assessment 2024The mission’s sensor pilots used flow meters, groundwater level sensors, chlorine analysers, pressure sensors and pump controllers.
PIB, 31 March 2021Under the extended mission, every rural water scheme gets a Sujal Gaon ID and is mapped digitally from source to tap.
PIB, Ministry of Jal Shakti, 13 March 2026
Industries where it applies
Each industry page sets out its equipment, its rules and the other use cases that run there.
Questions buyers ask
Ask about your own network, plant or campus. An engineer will reply.
Contact us01What if mobile coverage at the village is weak?
Coverage and power are checked for each site before installation. The controller works over 4G/LTE with two SIM slots, and battery-powered sensors can report over a long-range wireless link to a gateway placed where the signal is good.
02Does the pump stop when the tank is full?
Yes. The pump runs on the tank’s own level: it starts at the low mark and stops at the high one. An alert is raised if a tank overflows or a pump is about to run dry.
03What does the local operator need?
A phone with the IoTyX app. An authorised operator sees the tank level and starts or stops the pump from it, and each command is confirmed and logged.
04Can one engineer watch several villages?
Yes. Each village appears on one map with its quantity, pressure, quality and system status, and each engineer sees the villages they are responsible for.
