Industries: Rural water
For water schemes that serve villages.
Rural schemes are spread over long distances with few staff. Ilonnati runs each pump on its tank’s level and shows every village’s quantity, pressure and quality on one screen.
- Use cases
- 4 described below
- To start
- A pilot at one site
On a typical site
- Elevated reservoir
- Pump set
- Motorised valve
- Meter at each connection
- Ilonnati controller
In short
A rural scheme may serve one village from a borewell or many from a shared source, through service reservoirs and overhead tanks, out to household connections at the tail end. Pumps are switched by hand, tanks overflow or run dry, and an engineer may hear of a fault days later. Ilonnati places a controller at the pump house and level sensors in the tanks, so pumps follow the tank’s level, with a bulk meter at the source, pressure sensors on the lines and meters at households. IoTyX shows quantity, pressure, quality and system status for every village, on a phone or in the office.
Why it is hard
The challenges
What makes rural water hard to run without live measurement.
What Ilonnati runs herePumps switched by hand
A local operator walks to the pump house to start and stop the pump, so tanks overflow or run dry depending on when they get there.
The tail end
Homes at the end of the line get the least water and the lowest pressure, and the shortfall is reported late, if at all.
Distance
Villages in a scheme lie far apart, and an engineer covering many of them learns of a fault on the next visit.
Quality at the source
Water from borewells and springs varies, and it is tested by occasional sampling rather than measured as it is supplied.
Keeping a scheme running
A scheme works only while it is operated and maintained; without readings, a failing pump or a leaking main shows only when supply stops.
What Ilonnati measures and runs
Ilonnati controllers and sensors on the equipment, IoTyX on the screen.
Tank level
Overhead tanks and service reservoirs report their level, and the pump starts and stops on it.
Water drawn and supplied
A bulk meter at the source and meters at households show what is drawn and what each home receives.
Tail-end pressure
Pressure on the distribution lines shows whether the last connections are being served.
Water quality
pH and turbidity at the intake and in the tank, with an alert when a reading leaves its limit.
Pump and device status
Whether each pump is running and each device is reporting, with an alert for any that goes offline.
Use cases
Each has a page of its own: the situation, how it works and what is measured.
Rural water supplyVillage schemes from the borewell to the overhead tank to the last household, with pumps that run on the tank’s level.MeasuresOverhead tank level, Water drawn at the source, Daily supply
Pump and reservoir automationPumps that run on the tank’s level, and valves that deliver a set quantity at a set time, held at the controller.MeasuresTank and reservoir level, Sump level, Flow and running total
Water quality monitoringpH, turbidity, residual chlorine, TDS and nitrate measured continuously, from the treatment works to the far end.MeasurespH, Turbidity, Residual chlorine
Leak and theft detectionBursts, leaks, illegal draws and meter tampering found from flow and pressure, not from complaints.MeasuresZone inflow, Consumption at connections, Main pressure
The rules and programmes behind it
Public programmes and rules that ask for this kind of measurement. Each links to the body that publishes it.
55 L
Jal Jeevan Mission counts a rural tap as functional only if it gives at least 55 litres per person per day, of BIS 10500 quality, on a regular schedule.
Jal Jeevan Mission, Functionality Assessment 202476%
In the 2024 national assessment, 76% of rural household taps met all three tests. Damaged pipelines (31.9%) and pump failures (29.6%) were the most common reasons a tap stopped working.
Jal Jeevan Mission, Functionality Assessment 20242028
In March 2026 the Cabinet extended Jal Jeevan Mission to December 2028 and moved its focus from building infrastructure to delivering service.
Cabinet decision, 10 March 2026The mission’s sensor pilots used flow meters, groundwater level sensors, chlorine analysers, pressure sensors and pump controllers.
PIB, 31 March 2021
Questions buyers ask
Ask about your own network, plant or campus. An engineer will reply.
Contact us01Does each village need someone on site?
Not to run the pump, which follows the tank’s level. The engineer sees every village on a phone or in the office and visits where an alert or a reading calls for it.
02What if mobile coverage is weak?
Coverage and power are checked for each site before installation. The controller works over 4G/LTE with two SIM slots, and battery-powered sensors can report over a long-range wireless link to a gateway placed where the signal is good.
03What about power at remote sites?
The controller runs on 5 to 60 V DC and has a backup battery that reports a power failure, and the tank sensors run on their own batteries. Power for each site is planned before installation.
Related industries
The same hardware and the same platform, set up for other sites in water and utilities and beyond.
Water and utilitiesWater utilitiesCity and town water boards: reservoirs, zones, valves and meters, measured and run from the control room.
Water and utilitiesTransportRailway stations and bus stands: drinking-water quality measured at the tap and shown to passengers.
Campuses and buildingsHousing communitiesGated communities, apartment societies and row houses: tanks that refill themselves, metered homes and leak alerts.
Campuses and buildingsCommercial buildings and campusesOffices, malls, SEZs, IT parks and large campuses: water, energy and daily operations measured on one platform.
