Industries: Pharmaceuticals
Pharmaceutical water, measured grade by grade.
Continuous quality readings for Water for Injections, Purified Water and water for extracts, and the pumps, HVAC and energy behind production, on one platform.
- Use cases
- 5 described below
- To start
- A pilot at one site
In the drawing
A production block, stainless water tanks, a purified-water loop with a probe, and an Ilonnati controller.
In short
Water touches almost everything a pharmaceutical plant makes. It is an excipient, the vehicle for reconstitution, part of synthesis and the rinse for vessels, equipment and primary packaging, and each use needs its own grade. Quality, above all microbiological quality, is a constant concern, and plants put considerable resources into their purification systems. Ilonnati measures the quality of each grade continuously where it is made, stored and used, keeps every reading with its time and place, and raises an alert when a reading leaves its band. The pumps, motors and HVAC plant behind production, and the energy they use, are watched on the same platform.
Why it is hard
The challenges
What makes pharmaceuticals hard to run without live measurement.
What Ilonnati runs hereSeveral grades, several standards
Water for Injections, Purified Water and water for extracts each have their own quality requirements, set by pharmaceutical regulators.
Microbiological quality
Control of water quality, microbiological quality above all, is a major concern, and a purification system needs constant care to hold it.
Gaps between samples
A laboratory sample shows the water at the moment it was drawn; a drift between samples is found only at the next result.
Records kept by hand
Quality readings are often logged by hand beside each instrument, which makes review slow and gaps easy to miss.
Utilities that cannot stop
Pumps, HVAC and purification plant run around the clock, and a failure among them can halt production.
What Ilonnati measures and runs
Ilonnati controllers and sensors on the equipment, IoTyX on the screen.
Water for Injections
Quality measured continuously where it is generated, stored and drawn for parenteral medicines.
Purified Water
Conductivity, pH and dissolved solids on the loop and at points of use, with an alert when a reading leaves its band.
Water for extracts
The quality of water drawn to prepare drug extracts, measured and kept on record like the other grades.
Feed water
Chlorine, turbidity and dissolved solids in the water entering the purification system, before treatment.
HVAC and pumps
Vibration, temperature, voltage and current on the HVAC plant and pumps that production depends on.
Energy
Use by source and by machine, set against output, to show the energy behind each unit produced.
Use cases
Each has a page of its own: the situation, how it works and what is measured.
Pharma water qualityPurified Water, Water for Injections and water for extracts, each watched against the quality its grade demands.MeasuresConductivity, pH, Total dissolved solids
Process water and effluentFresh, cooling and process water measured where it is drawn and used, and effluent checked before it leaves.MeasuresIntake flow, Cooling and process flow, pH
Predictive maintenanceVibration, temperature, voltage and current on pumps, motors and HVAC, so a fault is found before the machine stops.MeasuresVibration, Temperature, Voltage
Energy managementGrid, solar, wind, battery and generator supply in one view, down to the LT panel and each machine.MeasuresSupply by source, Voltage, Current
Water quality monitoringpH, turbidity, residual chlorine, TDS and nitrate measured continuously, from the treatment works to the far end.MeasurespH, Turbidity, Residual chlorine
The rules and programmes behind it
Public programmes and rules that ask for this kind of measurement. Each links to the body that publishes it.
17
CPCB requires the 17 most polluting industry categories, with common effluent and sewage treatment plants, to stream effluent and emission readings to CPCB and the State Board in real time.
CPCB, real-time effluent monitoring guidelines, 2014Any project that needs a CGWA groundwater permit must fit a digital flow meter with telemetry on every borewell.
CGWA guidelines, 2020, Ministry of Jal Shakti
Questions buyers ask
Ask about your own network, plant or campus. An engineer will reply.
Contact us01Which grades of water can be monitored?
Water for Injections, Purified Water and water for preparing drug extracts, each against the quality requirements of its grade.
02Does continuous monitoring replace laboratory tests?
No. It shows how the water behaves between samples; the plant’s laboratory testing, including its microbiological tests, goes on as before.
03Can the plant’s utilities be monitored too?
Yes. Pumps, motors and HVAC plant are watched for vibration, temperature, voltage and current, and energy is measured by source and by machine, on the same platform.
Related industries
The same hardware and the same platform, set up for other sites in industry and energy and beyond.
Industry and energyCementKilns, crushers, conveyors and mills watched as one plant through a digital twin, with energy measured per machine.
Industry and energyIron and steelCooling and process water measured by quantity and quality, with the plant’s motors, energy and gas watched alongside.
Industry and energyPower and energyFresh water for cooling measured and kept to need, and every source of power on a site monitored down to the panel.
Industry and energyChemicals and fertilisersWater drawn, used and discharged, effluent checked against its norms, and gas and safety watched across the plant.
