Industries: Power and energy
Cooling water and power, measured together.
For a thermal station, the fresh water drawn for cooling, measured from intake to discharge; for any large producer or user, energy from every source, down to the low-tension panel.
- Use cases
- 6 described below
- To start
- A pilot at one site
On a typical site
- Rotary kiln
- Drive motor
- Substation
- Solar and wind
- Ilonnati controller
In short
A thermal power station depends on fresh water to cool it, and drought or flood can put that supply, and with it the security of generation, at risk. Ilonnati measures the fresh water a plant draws and uses, from intake to cooling circuits to discharge, so that use is controlled to the plant’s requirements. On the electrical side, it monitors energy from the grid, wind, solar, battery storage and generators, with low-tension panels watched for overcurrent, voltage deviation and power quality. Policy-based alerts flag a threshold crossed or a trend drifting, and the station’s pumps, motors and fans are watched for the signs of a developing fault.
Why it is hard
The challenges
What makes power and energy hard to run without live measurement.
What Ilonnati runs hereDependence on fresh water
Thermal generation needs large volumes of fresh water for cooling, and a short supply limits what the station can generate.
Drought and flood
Both disturb the water a plant can draw, and with it the security of the energy it supplies.
Many sources of power
Grid, solar, wind, batteries and generators each have their own meter, if any, and are rarely seen together.
Faults found by tripping
Overcurrent and voltage deviation on low-tension panels often show up only when equipment trips.
What Ilonnati measures and runs
Ilonnati controllers and sensors on the equipment, IoTyX on the screen.
Fresh water intake
What the plant draws from each source, metered continuously, so use is kept to what the plant requires.
Cooling circuits
Flow, conductivity and pH on cooling water, to show make-up, blowdown and the build-up of salts.
Generation sources
Grid, wind, solar, battery storage and backup generators in one view of the site’s energy.
LT panels
Overcurrent, voltage deviation and power quality from each low-tension panel, as they happen.
Battery banks
Status and health of battery storage, logged so a weak bank is found before it is needed.
Pumps, fans and motors
Vibration, temperature, voltage and current on the auxiliaries a station depends on.
Use cases
Each has a page of its own: the situation, how it works and what is measured.
Process water and effluentFresh, cooling and process water measured where it is drawn and used, and effluent checked before it leaves.MeasuresIntake flow, Cooling and process flow, pH
Energy managementGrid, solar, wind, battery and generator supply in one view, down to the LT panel and each machine.MeasuresSupply by source, Voltage, Current
Predictive maintenanceVibration, temperature, voltage and current on pumps, motors and HVAC, so a fault is found before the machine stops.MeasuresVibration, Temperature, Voltage
Industrial safety monitoringGas leaks, vibration, noise, air quality and worker exposure measured across a plant, with alerts at the thresholds.MeasuresGas leaks, Noise, Vibration
Air quality monitoringOutdoor stations for particulates, gases and noise, reporting as often as every minute to a map.MeasuresPM2.5, PM10, Nitrogen dioxide (NO₂)
Environmental complianceAir, water and noise measured around the clock at a site, each reading checked against its limit as it arrives.MeasuresPM2.5 and PM10, NO₂, SO₂ and CO, Noise
The rules and programmes behind it
Public programmes and rules that ask for this kind of measurement. Each links to the body that publishes it.
1,333
Under the PAT scheme, 1,333 large energy users in 13 sectors have energy-saving targets; in 2022–23 they saved 25.77 million tonnes of oil equivalent.
PAT scheme, PIB, Ministry of Power, 29 July 202417
CPCB requires the 17 most polluting industry categories, with common effluent and sewage treatment plants, to stream effluent and emission readings to CPCB and the State Board in real time.
CPCB, real-time effluent monitoring guidelines, 2014
Questions buyers ask
Ask about your own network, plant or campus. An engineer will reply.
Contact us01How does it help a thermal plant with water?
It measures the fresh water the plant draws and uses, from intake to cooling circuits to discharge, so its use can be kept to what the plant requires.
02Which energy sources can be monitored?
Grid supply, wind, solar, battery storage and backup generators, together with the low-tension panels they feed.
03Can alerts follow our own rules?
Yes. Alerts are configured by policy, for thresholds crossed and for trends that drift, and sent to the people responsible.
Related industries
The same hardware and the same platform, set up for other sites in industry and energy and beyond.
Industry and energyCementKilns, crushers, conveyors and mills watched as one plant through a digital twin, with energy measured per machine.
Industry and energyPharmaceuticalsThe grades of water a pharmaceutical plant depends on, measured continuously, with its utilities watched alongside.
Industry and energyIron and steelCooling and process water measured by quantity and quality, with the plant’s motors, energy and gas watched alongside.
Industry and energyChemicals and fertilisersWater drawn, used and discharged, effluent checked against its norms, and gas and safety watched across the plant.
