Industry and energy
The hazards on a plant floor, measured.
Detectors and wearables measure gas leaks, noise, vibration, air quality and each worker’s exposure, and a risk map shows where on the site the readings are rising.
- In the field
- Ilonnati controllers and sensors
- On the screen
- IoTyX: web, phone, control room
On a typical site
- Rotary kiln
- Drive motor
- Substation
- Solar and wind
- Ilonnati controller
In short
Most plants measure their hazards at a few points, now and then, with a hand-held instrument. Ilonnati places detectors across the site for gas leaks, vibration, noise and air quality, and wearables that measure the exposure of the people working there. Readings reach IoTyX as they are taken and are placed on a risk map of the site, so a hazard is seen where it is, not only as a number. A reading that crosses its threshold alerts the people responsible at once. Over time, predictive analytics and digital twins of individual assets show where risks are building.
Who it is for
- Safety and environment managers
- Chemical, fertiliser and steel plants
- Power stations and heavy industry
- Mines and large industrial sites
- Plant heads answerable for worker safety
Before and after
What changes
The same job, today and with Ilonnati.
- Today: Gas is checked with a hand-held detector on a round. With Ilonnati: Fixed detectors measure gas continuously and raise an alert as soon as a leak is detected.
- Today: Noise is measured during a periodic survey. With Ilonnati: Noise is measured continuously at the places people work.
- Today: A worker’s exposure is estimated from where they were rostered. With Ilonnati: Wearables measure each worker’s exposure through the shift.
- Today: Readings sit in separate logbooks, one per hazard. With Ilonnati: Every hazard reading sits on one risk map of the site.
- Today: A rising pattern is noticed after an incident. With Ilonnati: Trends are analysed, so a hazard that is building is seen early.
How it works
From the reading in the field to the action on the screen, and back.
- 01
Map the risks
The site’s hazards are mapped with its safety team: where gas could leak, where noise is high, where people work.
- 02
Detectors and wearables
Fixed detectors are placed at those points, and wearables are issued to the people whose exposure must be measured.
- 03
Live on the map
Readings reach IoTyX as they are taken, each shown at its place on the site’s risk map.
- 04
A threshold is crossed
Gas near a storage area rises past its threshold, and the shift in-charge and the safety officer are alerted at once.
- 05
Respond and record
The area is cleared and checked, and the readings before and after stay on record for the investigation.
- 06
Patterns over months
Analysis of the record shows where readings rise again and again, so controls go where the risk is.
What is measured
Each reading reaches IoTyX through the Ilonnati controller beside the equipment.
| Reading | What it tells you |
|---|---|
| Gas leaks | A release near storage, pipework or process equipment, as it starts |
| Noise | Levels at work positions, against the limits that apply |
| Vibration | Machines and structures shaking beyond their usual pattern |
| Air quality | Dust and gases such as CO, NO₂ and SO₂ in the air people breathe |
| Worker exposure | What each person was exposed to through the shift, from a wearable |
| Place on the risk map | Where each reading was taken, and where hazards cluster |
Industries where it applies
Each industry page sets out its equipment, its rules and the other use cases that run there.
Questions buyers ask
Ask about your own network, plant or campus. An engineer will reply.
Contact us01What does it measure?
Gas leaks, vibration, noise, air quality and the exposure levels of workers, through fixed detectors and wearables.
02Who is alerted when a threshold is crossed?
The people responsible for that area, by push notification, email and in the IoTyX app. Thresholds are set per sensor.
03What is the risk map?
A geospatial map of the site with every safety reading at the place it was taken, so the team sees where hazards are and where they cluster.
04Does it replace the plant’s existing safety systems?
It is designed around what the plant already has. What it measures, and how it sits beside existing systems, is agreed for each project.
